The air inside your crawl space becomes the air inside your home. JCB Waterproofing and Construction's full encapsulation service seals your home's foundation level against moisture, pests, and mold.
What makes our encapsulation installs last decades, not years.
Heavy puncture-resistant poly barriers stay intact through decades of crawl space activity, inspection visits, and seasonal ground movement.
We seal every penetration -- pipes, posts, and support columns -- individually so the barrier is continuous with no gaps that allow moisture to bypass the system.
HVAC equipment running in an encapsulated crawl space operates at higher efficiency because humidity does not overload the system's dehumidification capacity.
We inspect floor joists, beams, and support posts as part of every assessment and flag any existing wood damage that requires remediation before encapsulation is installed.
The science behind crawl space encapsulation centers on moisture vapor transmission from exposed soil surfaces. Even dry-looking crawl space soil emits moisture vapor continuously at a rate that can introduce gallons of water per day into the air under your home. Traditional building practice placed foundation vents to exhaust this moisture, but research has repeatedly shown that venting in humid climates introduces more moisture than it removes, because the air flowing in from outside is often more humid than the air inside the crawl space. Sealing the crawl space and managing its humidity with a rated dehumidifier consistently outperforms venting in WI climates.
The vapor barrier is the physical core of the encapsulation system. Mil thickness matters significantly in this application: 6-mil poly is standard for short-term vapor retarders in above-grade construction, but crawl space conditions include foot traffic during inspections and maintenance, contact with rough aggregate and irregular soil surfaces, rodent activity, and exposure to moisture for decades. We specify a minimum 20-mil reinforced poly with a ripstop layer that resists puncture from debris and maintains its vapor transmission rating even if the surface is scuffed or walked on. The barrier is cut and fitted to the exact dimensions of each crawl space section, with all wall terminations run up to the rim joist and sealed with a waterproof tape rated for that adhesion surface.
Wood rot in crawl space framing begins when wood moisture content exceeds approximately 19 to 20 percent and stays elevated long enough for decay fungi to establish. Decay fungi are present in virtually all soil and all crawl space environments -- the limiting factor is not their presence but the moisture level that allows them to become active. Floor joists exposed to a wet crawl space can develop visible decay within a few wet seasons, and the damage is progressive: soft spots in floors, squeaking from weakened joists, and in severe cases structural deflection in floor systems become evident. Our assessments photograph and document all floor joist and beam conditions so you understand the current state of your structure before and after encapsulation.
Mold remediation is frequently required in conjunction with encapsulation when visible mold colonies are already established on floor joists, subfloor sheathing, or HVAC components in the crawl space. We assess mold extent as part of every inspection and provide a remediation plan that addresses existing growth before the encapsulation barrier is installed. Installing a vapor barrier over active mold does not eliminate it -- the mold must be treated first to prevent it from continuing to develop and produce airborne spores that migrate into the living space. Our remediation process uses EPA-registered fungicidal treatments applied to all affected wood surfaces, followed by a borate-based preservative application to inhibit future growth.
Six crawl space services that address every moisture source under your Krakow home.
We cut and fit barrier material to every section of your crawl space, including around posts, piers, and columns, so no ground surface is left exposed to vapor evaporation.
Rated standalone crawl space dehumidifiers installed with gravity drain or condensate pump, sized to the cubic footage of your specific crawl space and set to maintain safe humidity levels year-round.
Existing foundation vents are sealed with rigid foam insulation cut to size and adhered with spray foam to eliminate the primary pathway for outside humid air to enter the crawl space.
Post-treatment borate preservative application inhibits future mold and decay fungi development on all treated wood surfaces under conditions of elevated humidity.
Drainage channels are integrated under the vapor barrier perimeter, routing water to a sump pit with a submersible pump sized for your drainage area.
We install weatherstripping and rigid foam panel inserts on all access points sized to provide an airtight fit that maintains the pressure balance of the sealed crawl space.
We enter the crawl space and conduct a systematic inspection of all floor and wall surfaces, document moisture meter readings at multiple locations, photograph all floor joist and beam conditions, and identify every source of water or moisture entry before recommending any course of action.
Standing water drainage infrastructure is also installed in this phase so the crawl space floor is dry and stable before the vapor barrier goes down.
Foundation vents are sealed with rigid foam insulation and spray foam adhesive, and the crawl space access hatch is fitted with an insulating door seal panel.
We take final moisture readings and photograph the completed installation before issuing your written warranty documentation and maintenance schedule.
Our floor joists were showing early decay when JCB Waterproofing and Construction inspected. They remediated the mold, sealed the entire crawl space, and installed a dehumidifier -- a year later the wood moisture readings are in the safe range and the floors feel solid again.
The crew was thorough and professional. They explained what they found, showed me photos, and completed the work exactly as quoted. The crawl space is completely dry now and looks professionally done.
I got four quotes and JCB Waterproofing and Construction was the only company that gave me a written spec listing the mil thickness of the poly they were installing. That transparency is why I chose them and their work backed it up completely.
Take the first step toward a healthier, drier home. Contact JCB Waterproofing and Construction for a same-day crawl space inspection.
Call +1-866-476-1348 Now